Posted By: Jon Arnett
Part out begins- 92' talon awd + performance parts - April 08, 2009 01:11 am UTC
So as per my epic thread:
http://ca.dsm.org/forums/ubbthreads.php?ubb=showflat&Number=269891#Post269891
After many people expressed interest, no one put any money in my hand. The part out starts now. I have alot of parts requested so far, but please message me with anything you want, if the first person falls through, you'll get second dibs.
Obviously all the other non performance add-ons are now available also, like the engine, transmission, etc., and the performance stuff is here:
Engine:
-EVO III-16G turbo (real version, not cheap chinese knock-off)
-Ported 2nd gen Exhaust manifold
-3” custom stainless steel exhaust, custom stainless hi-flow cat, custom stainless muffler
-Massive SS FMIC /w piping (this is not an ebay special, it's over 3" thick, good for over 750HP)
-2.5" stainless throttle body elbow
-Massive Aluminum race rad (Has fan mounts, and engine bay mounts for both 1G and 2G talons)
-Aeromotive aftermarket FPR, stainless lines, /w gauge
-550cc RC injectors
-2G MAF
-K&N Air filter
-ACT2900 clutch (good for 560+ft.lbs. torque with a street disc, no puck)
-Crushed BOV
-New Bosch O2 sensor (less than 500kms since install)
Electronics:
-SAFC-II
-Eprom ECU with chip for above engine mods and stutterbox (launch control)
-VDO Boost Gauge
-Data logging cable
-Kenwood MP3 cd player with kenwood 6x9’s in rear (ipod wire already installed)
Suspension/Brakes:
-Crossdrilled front rotors
-PBR Metalmaster front brake pads
-New Rear OEM rotors (with less than 500kms on them)
-New Rear OEM pads (with less than 500kms on them)
-Stainless steel brake lines
-Apexi lowering springs (1.5” drop)
-Koni Yellow front shocks
-Koni OEM replacement rear shocks
Other:
-17” Motegi MR-7 Gunmetal wheels with tuner lugs
-17” Kumho ecsta 712’s (1-2 seasons left)
-15" Steelies with standard lugs
-15" Blizzaks (1-2 seasons left)
I put some rough pricing in the other thread also, but just let me know what you want, and your offer, and we'll work it out. I'm sending out PMs to everyone that's already messaged me, so if you've sent something and don't get a message tonight, send one again cause I've missed you.
Pictures for determining condition can be done in a matter of hours from when you message me.
The only other thing to mention is that I don't have any engine hoist, so if you want that, we'll need to arrange some way to pull it. Yes engine runs fine currently /w 178,000 original kms on it.
http:/
After many people expressed interest, no one put any money in my hand. The part out starts now. I have alot of parts requested so far, but please message me with anything you want, if the first person falls through, you'll get second dibs.
Obviously all the other non performance add-ons are now available also, like the engine, transmission, etc., and the performance stuff is here:
Engine:
-EVO III-16G turbo (real version, not cheap chinese knock-off)
-Ported 2nd gen Exhaust manifold
-3” custom stainless steel exhaust, custom stainless hi-flow cat, custom stainless muffler
-Massive SS FMIC /w piping (this is not an ebay special, it's over 3" thick, good for over 750HP)
-2.5" stainless throttle body elbow
-Massive Aluminum race rad (Has fan mounts, and engine bay mounts for both 1G and 2G talons)
-Aeromotive aftermarket FPR, stainless lines, /w gauge
-550cc RC injectors
-2G MAF
-K&N Air filter
-ACT2900 clutch (good for 560+ft.lbs. torque with a street disc, no puck)
-Crushed BOV
-New Bosch O2 sensor (less than 500kms since install)
Electronics:
-SAFC-II
-Eprom ECU with chip for above engine mods and stutterbox (launch control)
-VDO Boost Gauge
-Data logging cable
-Kenwood MP3 cd player with kenwood 6x9’s in rear (ipod wire already installed)
Suspension/Brakes:
-Crossdrilled front rotors
-PBR Metalmaster front brake pads
-New Rear OEM rotors (with less than 500kms on them)
-New Rear OEM pads (with less than 500kms on them)
-Stainless steel brake lines
-Apexi lowering springs (1.5” drop)
-Koni Yellow front shocks
-Koni OEM replacement rear shocks
Other:
-17” Motegi MR-7 Gunmetal wheels with tuner lugs
-17” Kumho ecsta 712’s (1-2 seasons left)
-15" Steelies with standard lugs
-15" Blizzaks (1-2 seasons left)
I put some rough pricing in the other thread also, but just let me know what you want, and your offer, and we'll work it out. I'm sending out PMs to everyone that's already messaged me, so if you've sent something and don't get a message tonight, send one again cause I've missed you.
Pictures for determining condition can be done in a matter of hours from when you message me.
The only other thing to mention is that I don't have any engine hoist, so if you want that, we'll need to arrange some way to pull it. Yes engine runs fine currently /w 178,000 original kms on it.
Don't worry, you still have dibs.