Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
installed meth and looking for advice #449415
June 24, 2016 10:06 pm UTC
June 24, 2016 10:06 pm UTC
Joined: Jun 2005
Posts: 398
Charlottetown PEI
John MacPhail Offline OP
Serious Member
John MacPhail  Offline OP
Serious Member
*****
Joined: Jun 2005
Posts: 398
Charlottetown PEI
Hi Guys: I have just installed a devils own meth kit to try to make a little more power on pump on the street.
I have it set with a hobbs switch to start at 13-14 psi with a .7 GPH nozzle turbo is @24 using 1G timing base map and evo8 stock fuel map for a start which i have changed a little. question I have is what AFR are should I be targeting with the meth spraying.
Thanks

1992 AWD Talon, MT, 6 bolt, Ebay 16G, @ 24 PSI, Evo 8 MAF, 3" DP, Cat delete,3" Exhaust AFX WB, Walbro 255 rewired, AFPR @43.5, FIC 950, FMIC 2.5" Pipe, 1G BOV, ECM Link V3, Meth 50/50 150psi .7GPH

Last edited by John MacPhail; June 24, 2016 10:08 pm UTC.

Dinosaurs evolved and learned to fly
This Dinosaur is evolving and learning to DSM
Re: installed meth and looking for advice [Re: John MacPhail] #449422
June 25, 2016 12:18 am UTC
June 25, 2016 12:18 am UTC
Joined: May 2010
Posts: 1,950
Guelph, Ontario
Jeremy Gilbert Offline
Serious Member
Jeremy Gilbert  Offline
Serious Member
***
Joined: May 2010
Posts: 1,950
Guelph, Ontario
I'm guessing you mean a 7 GPH.

I run a single 10 GPH with 50/50 mix, and I run about 12.2-12.4:1 AFRs and she seems to like it. As always, you wanna run whatever the car seems to like most.

Aim for low-mid 11's first, then pull fuel from there and see what she likes.


1995 TSi AWD
11.7@119 1.8 60' - Curse of the Bad Driver
PHP: 0
Re: installed meth and looking for advice [Re: John MacPhail] #449424
June 25, 2016 02:56 am UTC
June 25, 2016 02:56 am UTC
Joined: Jun 2005
Posts: 398
Charlottetown PEI
John MacPhail Offline OP
Serious Member
John MacPhail  Offline OP
Serious Member
*****
Joined: Jun 2005
Posts: 398
Charlottetown PEI
Hey Jeremy: yes 7 GPH nozzle in tb elbow, wow that seems lean as i have not used meth before. I gump tune for our 91, I will start in the 11's and see. thanks for the reply


Dinosaurs evolved and learned to fly
This Dinosaur is evolving and learning to DSM
Re: installed meth and looking for advice [Re: John MacPhail] #449426
June 25, 2016 04:04 am UTC
June 25, 2016 04:04 am UTC
Joined: May 2010
Posts: 1,950
Guelph, Ontario
Jeremy Gilbert Offline
Serious Member
Jeremy Gilbert  Offline
Serious Member
***
Joined: May 2010
Posts: 1,950
Guelph, Ontario
I'm on 94 pump, probably should have mentioned that. And yeah it seemed lean to me at first as well; like I said, I gave the car what it wanted. After doing some reading though it actually seems about the same as other guys with a similar setup; remember that meth is a fuel itself.


1995 TSi AWD
11.7@119 1.8 60' - Curse of the Bad Driver
PHP: 0
Re: installed meth and looking for advice [Re: John MacPhail] #449433
June 25, 2016 03:39 pm UTC
June 25, 2016 03:39 pm UTC
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Bryan Lawrence Offline
Senior Member, with Far TOO Much Time on Their Hands
Bryan Lawrence  Offline
Senior Member, with Far TOO Much Time on Their Hands
***
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
I think even with meth and your boost turned up the 1g map is still really aggressive, then add the evo fuel map on top of that I would be careful.

I assume you have a tune from before meth went in?


"Old Blue" 91 Talon TSi AWD
"Super Enthusiast" 91 Talon TSi AWD
Checkout DSMFAQ.com!
Re: installed meth and looking for advice [Re: John MacPhail] #449435
June 25, 2016 04:24 pm UTC
June 25, 2016 04:24 pm UTC
Joined: Jun 2005
Posts: 398
Charlottetown PEI
John MacPhail Offline OP
Serious Member
John MacPhail  Offline OP
Serious Member
*****
Joined: Jun 2005
Posts: 398
Charlottetown PEI
I have done a couple of pulls with this and not getting any knock with the meth. I do have 2 tunes from before meth went on a sloth tune for the street on 18 psi and one for the track on 22 psi when i add q16 to get some octane, 91 sucks


Dinosaurs evolved and learned to fly
This Dinosaur is evolving and learning to DSM
Re: installed meth and looking for advice [Re: John MacPhail] #449438
June 25, 2016 06:28 pm UTC
June 25, 2016 06:28 pm UTC
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Jason Drew Online content
Insane Member
Jason Drew  Online Content
Insane Member
*****
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
I tune mine around 11.5 on 93 or 94 with a 10gph nozzle.

One thing I will highly advise is using ecmlink to control it. Far easier tuning. Ecmlink will pull the global to adjust the fuel ratio automatically, no screwing around.


1997 Eclipse GST - AWD swapped - TPC - GT Spec powered
2023 - 9.63 - 145mph
Re: installed meth and looking for advice [Re: John MacPhail] #449460
June 27, 2016 03:51 pm UTC
June 27, 2016 03:51 pm UTC
Joined: Jan 2006
Posts: 2,241
Stratford/London
Mike Kuttschrutter Offline
Insane Member
Mike Kuttschrutter  Offline
Insane Member
***
Joined: Jan 2006
Posts: 2,241
Stratford/London
I use Map switching on my evo8 ecu.
I'm sure its the same idea with ecmlink.

I adjusted the global for fuel.
And just copied my timing maps, and ran a bunch of extra timing on the AltMap.

Pump turns on around 8psi with a 12 or 14 nozzle(I forget), maps switch, little red led turns on, and basically VTech and some wizard magic happens. AFR's are high 11's dips into the 12's occasionally.

I have also been told you can shoot for 12.5... but my balls haven't been big enough to attempt that yet.


Stock.
Re: installed meth and looking for advice [Re: Jeremy Gilbert] #449466
June 27, 2016 08:30 pm UTC
June 27, 2016 08:30 pm UTC
Joined: Aug 2003
Posts: 3,196
Newmarket, Ontario
Daren Peacock Offline
Insane Member
Daren Peacock  Offline
Insane Member
*****
Joined: Aug 2003
Posts: 3,196
Newmarket, Ontario
Originally Posted by Jeremy Gilbert
I'm guessing you mean a 7 GPH.

I run a single 10 GPH with 50/50 mix, and I run about 12.2-12.4:1 AFRs and she seems to like it. As always, you wanna run whatever the car seems to like most.

Aim for low-mid 11's first, then pull fuel from there and see what she likes.


Wow, seems pretty lean, what kind of boost & timing are you running & on what turbo?

I run 94, think I have an M12 nozzle in there, 50/50, with their older pump (probably their first gen, not sure if its 100 or 150 psi, have had one of their new 250psi pumps sitting on the shelf for years....). If I go much leaner then 10.5:1, I start to knock (~10.5 at peak cylinder pressure & lean out to ~11:1 as the rpms increase), boost ~30psi.

Originally Posted by Jason Drew


One thing I will highly advise is using ecmlink to control it. Far easier tuning. Ecmlink will pull the global to adjust the fuel ratio automatically, no screwing around.


Haven't played with these Link settings for some time, have they changed options for how meth is controlled? Thought mine was setup so when the set point is triggered , it enables the secondary fuel map (& not actually altering the global)?

Last edited by Daren Peacock; June 27, 2016 08:42 pm UTC.

98 Eclipse GSX DSM82HTA
Re: installed meth and looking for advice [Re: Daren Peacock] #449478
June 28, 2016 01:16 pm UTC
June 28, 2016 01:16 pm UTC
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Jason Drew Online content
Insane Member
Jason Drew  Online Content
Insane Member
*****
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Originally Posted by Daren Peacock

Originally Posted by Jason Drew


One thing I will highly advise is using ecmlink to control it. Far easier tuning. Ecmlink will pull the global to adjust the fuel ratio automatically, no screwing around.


Haven't played with these Link settings for some time, have they changed options for how meth is controlled? Thought mine was setup so when the set point is triggered , it enables the secondary fuel map (& not actually altering the global)?


They've updated it a bit the last update, more ways to trigger, can enable secondarys or adjust the global and deadtime.


1997 Eclipse GST - AWD swapped - TPC - GT Spec powered
2023 - 9.63 - 145mph
Re: installed meth and looking for advice [Re: Jason Drew] #449480
June 28, 2016 04:37 pm UTC
June 28, 2016 04:37 pm UTC
Joined: Aug 2003
Posts: 3,196
Newmarket, Ontario
Daren Peacock Offline
Insane Member
Daren Peacock  Offline
Insane Member
*****
Joined: Aug 2003
Posts: 3,196
Newmarket, Ontario
Originally Posted by Jason Drew
Originally Posted by Daren Peacock

Originally Posted by Jason Drew


One thing I will highly advise is using ecmlink to control it. Far easier tuning. Ecmlink will pull the global to adjust the fuel ratio automatically, no screwing around.


Haven't played with these Link settings for some time, have they changed options for how meth is controlled? Thought mine was setup so when the set point is triggered , it enables the secondary fuel map (& not actually altering the global)?


They've updated it a bit the last update, more ways to trigger, can enable secondarys or adjust the global and deadtime.


Good to know, I'm probably out of date on the software, will have to check it out.


98 Eclipse GSX DSM82HTA
Re: installed meth and looking for advice [Re: John MacPhail] #451436
October 23, 2016 10:42 pm UTC
October 23, 2016 10:42 pm UTC
Joined: May 2015
Posts: 126
PEI, Canada
Ben Stretch Offline
Regular Member
Ben Stretch  Offline
Regular Member
Joined: May 2015
Posts: 126
PEI, Canada
Hey guys. So i finished installing my meth kit today. Fun project and seems to be working as expected. I do have a question i'm hoping someone can help with. I think I understand it correctly but i'd like someone to confirm.

I'm using ECMlink V3 full to trigger the pump by way of the FPS output and relay. I have the activation conditions set to 2500 RPM, 86% TPS, 1.8 load and knock greater >= 0* and less than 5*. I understand that with V3 full you can enable the MINOCT maps as secondary maps when FPS is active. For now I have my MIN and MAX tables matching until i confirm everything is working right and consistence before I start tweaking.

My question is, the way i have this set up if the ECU sees greater than 5* knock it will not enable the FPS because all the conditions aren't met? Assuming this is true, does this also mean it will switch back and use the MAXOCT table? Put another way, does link use the MAX table exclusively unless all the FPS activation conditions are met?

If this is right, I plan to use the MAX table for a conservative 91 pump tune and dial in the MIN tables for meth. I just need to be sure i have the ECMLink logic right so that if the pump fails or the nozzle gets clogged resulting an a bunch of knock, it will revert to the MAX tables with more conservative timing and fuel. Of course it won't pull boost since i have a MBC but i think this is a pretty good failsafe..ish?

Let me know if im off my rocker


1996 "Canary" Talon...give it any gas and it's dead
Re: installed meth and looking for advice [Re: John MacPhail] #451437
October 24, 2016 12:41 am UTC
October 24, 2016 12:41 am UTC
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Jason Drew Online content
Insane Member
Jason Drew  Online Content
Insane Member
*****
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
You want to max out the knock option, you don't ever want it cutting out due to knock.

This is my current setup

[Linked Image]


1997 Eclipse GST - AWD swapped - TPC - GT Spec powered
2023 - 9.63 - 145mph
Re: installed meth and looking for advice [Re: John MacPhail] #451439
October 24, 2016 01:24 am UTC
October 24, 2016 01:24 am UTC
Joined: May 2015
Posts: 126
PEI, Canada
Ben Stretch Offline
Regular Member
Ben Stretch  Offline
Regular Member
Joined: May 2015
Posts: 126
PEI, Canada
Thanks for the details Jason. I can see why you wouldn't want to stop spraying meth if you got knock but wouldn't it be better to drop the timing and add fuel by switching back to the pump gas tuned MAXOct table? Maybe this isn't how it works ?


1996 "Canary" Talon...give it any gas and it's dead
Re: installed meth and looking for advice [Re: John MacPhail] #451440
October 24, 2016 01:31 am UTC
October 24, 2016 01:31 am UTC
Joined: Jan 2006
Posts: 2,241
Stratford/London
Mike Kuttschrutter Offline
Insane Member
Mike Kuttschrutter  Offline
Insane Member
***
Joined: Jan 2006
Posts: 2,241
Stratford/London
Wow look at all those options. I'll have to look into this... I'm still using a pressure switch.

Pain in the butt when I ease on the throttle and bam compounds make 8psi and then next thing you know I'm spraying meth and at 20psi at 30% throttle.

Also I see the option to turn off on clutch switch. Do you guys not spray while on the 2 step???


Stock.
Re: installed meth and looking for advice [Re: Daren Peacock] #451441
October 24, 2016 03:04 am UTC
October 24, 2016 03:04 am UTC
Joined: May 2010
Posts: 1,950
Guelph, Ontario
Jeremy Gilbert Offline
Serious Member
Jeremy Gilbert  Offline
Serious Member
***
Joined: May 2010
Posts: 1,950
Guelph, Ontario
Originally Posted by Daren Peacock
Originally Posted by Jeremy Gilbert
I'm guessing you mean a 7 GPH.

I run a single 10 GPH with 50/50 mix, and I run about 12.2-12.4:1 AFRs and she seems to like it. As always, you wanna run whatever the car seems to like most.

Aim for low-mid 11's first, then pull fuel from there and see what she likes.


Wow, seems pretty lean, what kind of boost & timing are you running & on what turbo?


Sorry, somehow missed this first time around.

12.4:1 AFRs with 23psi out of an FP Green with about 14* timing made 460awhp/395tq.

I had it as high as 30psi with about 12.0:1 AFRs with no knock, but I wasn't watching my timing as I only did that to get an idea of when I might run out of injector (and wanted to see if my IATs would ever go up). I don't think I saved the logs though.

I'm fairly certain I have a 250psi meth pump.


1995 TSi AWD
11.7@119 1.8 60' - Curse of the Bad Driver
PHP: 0
Re: installed meth and looking for advice [Re: Ben Stretch] #451442
October 24, 2016 03:15 am UTC
October 24, 2016 03:15 am UTC
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Jason Drew Online content
Insane Member
Jason Drew  Online Content
Insane Member
*****
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Originally Posted by Ben Stretch
Thanks for the details Jason. I can see why you wouldn't want to stop spraying meth if you got knock but wouldn't it be better to drop the timing and add fuel by switching back to the pump gas tuned MAXOct table? Maybe this isn't how it works ?


If anything, I would add a solenoid valve and pressure sensor right before the nozzle and have it switch to a fail-safe map if pressure is lost, other than that, keep it spraying.

I'm not the meth expert by any means but this is what has worked for me.

Originally Posted by Mike Kuttschrutter
Wow look at all those options. I'll have to look into this... I'm still using a pressure switch.

Pain in the butt when I ease on the throttle and bam compounds make 8psi and then next thing you know I'm spraying meth and at 20psi at 30% throttle.

Also I see the option to turn off on clutch switch. Do you guys not spray while on the 2 step???


Link is the best option for controlling meth, hands down.

In my experience, there's no need to spray on the 2-step, not enough load to cause knock.

Originally Posted by Jeremy Gilbert
Originally Posted by Daren Peacock
Originally Posted by Jeremy Gilbert
I'm guessing you mean a 7 GPH.

I run a single 10 GPH with 50/50 mix, and I run about 12.2-12.4:1 AFRs and she seems to like it. As always, you wanna run whatever the car seems to like most.

Aim for low-mid 11's first, then pull fuel from there and see what she likes.


Wow, seems pretty lean, what kind of boost & timing are you running & on what turbo?


Sorry, somehow missed this first time around.

12.4:1 AFRs with 23psi out of an FP Green with about 14* timing made 460awhp/395tq.

I had it as high as 30psi with about 12.0:1 AFRs with no knock, but I wasn't watching my timing as I only did that to get an idea of when I might run out of injector (and wanted to see if my IATs would ever go up). I don't think I saved the logs though.

I'm fairly certain I have a 250psi meth pump.


I tune mine around 11.5, seems to be happy there on 94 + a single 14gph nozzle/250 psi pump, 75/25 mix at 35 psi/13* of peak timing.

The more meth you add, the richer you should run really, as the stoich ratio of methanol is around 6:1. Just takes some playing around to see what your motor likes.


1997 Eclipse GST - AWD swapped - TPC - GT Spec powered
2023 - 9.63 - 145mph
Re: installed meth and looking for advice [Re: John MacPhail] #451443
October 24, 2016 04:07 am UTC
October 24, 2016 04:07 am UTC
Joined: Aug 2009
Posts: 4,783
Belleville Ontario
Jay Stacey Offline
Senior Member, with Far TOO Much Time on Their Hands
Jay Stacey  Offline
Senior Member, with Far TOO Much Time on Their Hands
*****
Joined: Aug 2009
Posts: 4,783
Belleville Ontario
Sven.. Does your pump have the pressure relief switch on the end?


11.45@125,
stock bottom end 6bolt 2g head.
272 hks cams.
Holset hx35
Backyard biult!!
Re: installed meth and looking for advice [Re: John MacPhail] #451444
October 24, 2016 10:52 am UTC
October 24, 2016 10:52 am UTC
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Bryan Lawrence Offline
Senior Member, with Far TOO Much Time on Their Hands
Bryan Lawrence  Offline
Senior Member, with Far TOO Much Time on Their Hands
***
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Mr Drew, out of curriosity why did you decide to do it by rpm instead of boost? Easier to tune?


"Old Blue" 91 Talon TSi AWD
"Super Enthusiast" 91 Talon TSi AWD
Checkout DSMFAQ.com!
Re: installed meth and looking for advice [Re: Jason Drew] #451445
October 24, 2016 10:58 am UTC
October 24, 2016 10:58 am UTC
Joined: May 2015
Posts: 126
PEI, Canada
Ben Stretch Offline
Regular Member
Ben Stretch  Offline
Regular Member
Joined: May 2015
Posts: 126
PEI, Canada
Originally Posted by Jason Drew
If anything, I would add a solenoid valve and pressure sensor right before the nozzle and have it switch to a fail-safe map if pressure is lost, other than that, keep it spraying.

I'm not the meth expert by any means but this is what has worked for me.


Cool, thanks again. So how do you have the pressure switch and solenoid worked into the system? Is the pressure switch just an indicator light to confirm line pressure or is it somehow worked into link? How is the solenoid triggered vs the trigger to turn on the pump? Sorry for all the questions. I've done a lot of googling but most of the info is weak and outdated.

I thing I need to check the firmware version of my link since I don't have coolant temp and boost options on my version?


1996 "Canary" Talon...give it any gas and it's dead
Re: installed meth and looking for advice [Re: John MacPhail] #451446
October 24, 2016 11:12 am UTC
October 24, 2016 11:12 am UTC
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Bryan Lawrence Offline
Senior Member, with Far TOO Much Time on Their Hands
Bryan Lawrence  Offline
Senior Member, with Far TOO Much Time on Their Hands
***
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Pressure switched would be worked into link so it switches to your non meth map (hopefully the guys can say how this is done)
Your pump will always be on and should have a pressure shutoff, and the solenoid would be wired into link so that once you hit parameters the solenoid opens.

As for too many questions, no such thing. That's what this board is for!


"Old Blue" 91 Talon TSi AWD
"Super Enthusiast" 91 Talon TSi AWD
Checkout DSMFAQ.com!
Re: installed meth and looking for advice [Re: Bryan Lawrence] #451447
October 24, 2016 11:30 am UTC
October 24, 2016 11:30 am UTC
Joined: May 2015
Posts: 126
PEI, Canada
Ben Stretch Offline
Regular Member
Ben Stretch  Offline
Regular Member
Joined: May 2015
Posts: 126
PEI, Canada
Originally Posted by Bryan Lawrence
Your pump will always be on and should have a pressure shutoff, and the solenoid would be wired into link so that once you hit parameters the solenoid opens.


Always on you say! I don't think the old Devil's Own pump I bought (150 PSI surflo I think) has a pressure shut off but I'll look into this a little more. When I pressure tested it I just had the line open and then with the nozzle into a bucket. Might have to cap the end and see if it comes on and builds pressure and then switches off. That would make sense now that I think about it.

Any recomendations to source a pressure switch and solenoid?

Originally Posted by Bryan Lawrence
As for too many questions, no such thing. That's what this board is for!

Thanks Bryan. This is exactly why I posted here instead of the ECMlink forum. You guys are great!


1996 "Canary" Talon...give it any gas and it's dead
Re: installed meth and looking for advice [Re: Bryan Lawrence] #451448
October 24, 2016 11:34 am UTC
October 24, 2016 11:34 am UTC
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Jason Drew Online content
Insane Member
Jason Drew  Online Content
Insane Member
*****
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Originally Posted by Bryan Lawrence
Mr Drew, out of curriosity why did you decide to do it by rpm instead of boost? Easier to tune?


It's not, it's activated by load. That is the most accurate way to tune it.

The 4200rpm is just a number I picked. With my setup I'll never hit 1.5 load at 4200rpm, so I could set it at 2000, it doesn't really matter.


1997 Eclipse GST - AWD swapped - TPC - GT Spec powered
2023 - 9.63 - 145mph
Re: installed meth and looking for advice [Re: John MacPhail] #451449
October 24, 2016 01:39 pm UTC
October 24, 2016 01:39 pm UTC
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Bryan Lawrence Offline
Senior Member, with Far TOO Much Time on Their Hands
Bryan Lawrence  Offline
Senior Member, with Far TOO Much Time on Their Hands
***
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Ah ok, I saw the 4200 and just assume it came on then, it's been a while since I have seen a link log, will remember this when I get the car back on the road.

Originally Posted by Ben Stretch
Any recomendations to source a pressure switch and solenoid?
I would actually be curious to hear this as my car came with the solenoid and I still need a pressure sensor. Guys can you shed some light on what pressure and where you set it in link to switch timing maps/boost?


"Old Blue" 91 Talon TSi AWD
"Super Enthusiast" 91 Talon TSi AWD
Checkout DSMFAQ.com!
Re: installed meth and looking for advice [Re: John MacPhail] #451450
October 24, 2016 02:59 pm UTC
October 24, 2016 02:59 pm UTC
Joined: Nov 2006
Posts: 1,137
Kingston
P
Paul Sitarski Offline
Serious Member
Paul Sitarski  Offline
Serious Member
****
P
Joined: Nov 2006
Posts: 1,137
Kingston
I'm running the snow kit 2 nozzles
675ml and 225ml. Hp pump progressive kit.
Starts at 20psi and peaks at 35psi.
I'm able to get 18deg at 7500rpm. 12.3afr and 42psi of boost. 50 50 mixture.


TPG+Meth
Re: installed meth and looking for advice [Re: John MacPhail] #451451
October 24, 2016 03:16 pm UTC
October 24, 2016 03:16 pm UTC
Joined: Jan 2006
Posts: 2,241
Stratford/London
Mike Kuttschrutter Offline
Insane Member
Mike Kuttschrutter  Offline
Insane Member
***
Joined: Jan 2006
Posts: 2,241
Stratford/London
When using the FPS output in link, does that switch to Alt Maps as well, or do you still use an input to make it switch?


Stock.
Re: installed meth and looking for advice [Re: John MacPhail] #451452
October 24, 2016 03:23 pm UTC
October 24, 2016 03:23 pm UTC
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Jason Drew Online content
Insane Member
Jason Drew  Online Content
Insane Member
*****
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
There's an option to switch maps when FPS or EGR are active.


1997 Eclipse GST - AWD swapped - TPC - GT Spec powered
2023 - 9.63 - 145mph
Re: installed meth and looking for advice [Re: John MacPhail] #451453
October 24, 2016 03:35 pm UTC
October 24, 2016 03:35 pm UTC
Joined: Dec 2006
Posts: 1,287
ontario
Sven Hebbard Offline
Serious Member
Sven Hebbard  Offline
Serious Member
***
Joined: Dec 2006
Posts: 1,287
ontario
I've never understood.

Whats the point of mixing meth with water?

Meth has a flash point of almost double then gasoline, And it's a self cooling fuel. We battle freezing injectors open on the Rail car all the time.

Re: installed meth and looking for advice [Re: John MacPhail] #451454
October 24, 2016 03:49 pm UTC
October 24, 2016 03:49 pm UTC
Joined: Jan 2006
Posts: 2,241
Stratford/London
Mike Kuttschrutter Offline
Insane Member
Mike Kuttschrutter  Offline
Insane Member
***
Joined: Jan 2006
Posts: 2,241
Stratford/London
^^
you can just buy it in the form of washer fluid on the go at any gas station.

I hopped in my car yesterday and realized my meth tank was almost empty. So I stopped at TSC and got a bunch of washer fluid on sale. I don't think I'll ever take the time to mix more then 50/50.
Grab and Go


Stock.
Re: installed meth and looking for advice [Re: Jason Drew] #451455
October 24, 2016 03:50 pm UTC
October 24, 2016 03:50 pm UTC
Joined: May 2015
Posts: 126
PEI, Canada
Ben Stretch Offline
Regular Member
Ben Stretch  Offline
Regular Member
Joined: May 2015
Posts: 126
PEI, Canada
Originally Posted by Jason Drew
There's an option to switch maps when FPS or EGR are active.


This is the option I'm using. What I'd be curious to know/confirm is, when FPS (or EGR) is active, it selects the alternate map (MINOct) which you would presumable tune for meth timing and fuel. So does that mean that if any of the activation conditions ( the ones in Jason's snapshot above) are false, does the ECU stays in or reverts to the standard map (MAXOct)?

I wonder if there is a logable value in link that can tell you which table is being used at any given time?

Now I'm really being a pest. Sorry Jason! lol


1996 "Canary" Talon...give it any gas and it's dead
Re: installed meth and looking for advice [Re: Mike Kuttschrutter] #451456
October 24, 2016 04:02 pm UTC
October 24, 2016 04:02 pm UTC
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Jason Drew Online content
Insane Member
Jason Drew  Online Content
Insane Member
*****
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Originally Posted by Sven Hebbard
I've never understood.

Whats the point of mixing meth with water?

Meth has a flash point of almost double then gasoline, And it's a self cooling fuel. We battle freezing injectors open on the Rail car all the time.


It depends what you're using it for, if you want the cooling effects, water absorbs much more heat than meth. Obviously if you just want an octane boost, the more meth the better.

The #1 reason is safety, you can't see a methanol fire, supposedly concentrations 50% and below are not flammable.



Originally Posted by Ben Stretch
Originally Posted by Jason Drew
There's an option to switch maps when FPS or EGR are active.


This is the option I'm using. What I'd be curious to know/confirm is, when FPS (or EGR) is active, it selects the alternate map (MINOct) which you would presumable tune for meth timing and fuel. So does that mean that if any of the activation conditions ( the ones in Jason's snapshot above) are false, does the ECU stays in or reverts to the standard map (MAXOct)?

I wonder if there is a logable value in link that can tell you which table is being used at any given time?

Now I'm really being a pest. Sorry Jason! lol


Correct, if the conditions aren't met, no meth and no map switch.

You can log the FPS switch, so you'll know when it's pumping and also the map should switch too at the same time.

Originally Posted by Mike Kuttschrutter
^^
you can just buy it in the form of washer fluid on the go at any gas station.

I hopped in my car yesterday and realized my meth tank was almost empty. So I stopped at TSC and got a bunch of washer fluid on sale. I don't think I'll ever take the time to mix more then 50/50.
Grab and Go


Be careful with that, actual concentration varies a LOT.


1997 Eclipse GST - AWD swapped - TPC - GT Spec powered
2023 - 9.63 - 145mph
Re: installed meth and looking for advice [Re: Jason Drew] #451457
October 24, 2016 04:23 pm UTC
October 24, 2016 04:23 pm UTC
Joined: May 2015
Posts: 126
PEI, Canada
Ben Stretch Offline
Regular Member
Ben Stretch  Offline
Regular Member
Joined: May 2015
Posts: 126
PEI, Canada
Originally Posted by Jason Drew
Correct, if the conditions aren't met, no meth and no map switch.

You can log the FPS switch, so you'll know when it's pumping and also the map should switch too at the same time.


Cool, thanks for your patience and info. I'll look into the press switch and solenoid.

Originally Posted by Mike Kuttschrutter
^^
you can just buy it in the form of washer fluid on the go at any gas station.

I hopped in my car yesterday and realized my meth tank was almost empty. So I stopped at TSC and got a bunch of washer fluid on sale. I don't think I'll ever take the time to mix more then 50/50.
Grab and Go

Originally Posted by Jason Drew
Be careful with that, actual concentration varies a LOT.




I pick up a gallon of deionized water for $2.49 and a gallon of methyl hydrate for $9.99 at CT. Should make the mix pretty consistent and 2 gallons for $13 isn't too bad. We'll see how long it last


1996 "Canary" Talon...give it any gas and it's dead
Re: installed meth and looking for advice [Re: John MacPhail] #451458
October 24, 2016 04:54 pm UTC
October 24, 2016 04:54 pm UTC
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Jason Drew Online content
Insane Member
Jason Drew  Online Content
Insane Member
*****
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
It lasts a while, I go through about 3-4 gallons of mix over the summer.


1997 Eclipse GST - AWD swapped - TPC - GT Spec powered
2023 - 9.63 - 145mph
Re: installed meth and looking for advice [Re: Jason Drew] #451460
October 24, 2016 05:11 pm UTC
October 24, 2016 05:11 pm UTC
Joined: Jan 2006
Posts: 2,241
Stratford/London
Mike Kuttschrutter Offline
Insane Member
Mike Kuttschrutter  Offline
Insane Member
***
Joined: Jan 2006
Posts: 2,241
Stratford/London
Originally Posted by Jason Drew
It lasts a while, I go through about 3-4 gallons of mix over the summer.


ummm? I go through my 2 gallon tank in a weekend.... wtf must be siphoning like crazy.... this is good to know

Last edited by Mike Kuttschrutter; October 24, 2016 05:17 pm UTC.

Stock.
Re: installed meth and looking for advice [Re: Mike Kuttschrutter] #451461
October 24, 2016 06:18 pm UTC
October 24, 2016 06:18 pm UTC
Joined: May 2010
Posts: 1,950
Guelph, Ontario
Jeremy Gilbert Offline
Serious Member
Jeremy Gilbert  Offline
Serious Member
***
Joined: May 2010
Posts: 1,950
Guelph, Ontario
Originally Posted by Paul Sitarski
I'm able to get 18deg at 7500rpm. 12.3afr and 42psi of boost. 50 50 mixture.


I see a lot of pros quoting numbers similar to this. I used to run 11.5AFR with about 22* timing; the leaner tune with less timing seems to be making a LOT more power. Which makes perfect sense to me.

Originally Posted by Mike Kuttschrutter
^^
you can just buy it in the form of washer fluid on the go at any gas station.


Careful with this. As Jason said, concentrations vary. Also, washer fluid is not ONLY water and meth - for one, pretty much any washer fluid will use colouring. After 1 season on CTC's green winter washer fluid, my pump, lines, and check valves were all gunked up with green sh!t. I mix my own 50/50 now and have never had a problem.

Meth also stores fairly well, it just absorbs water from the air. But a 50/50 mix in a sealed container won't absorb much water. I have a 3gal tank; every spring, I mix 4 gallons, fill the tank, and throw a spare gallon in the trunk. I've yet to need my spare.


1995 TSi AWD
11.7@119 1.8 60' - Curse of the Bad Driver
PHP: 0
Re: installed meth and looking for advice [Re: Mike Kuttschrutter] #451462
October 24, 2016 06:29 pm UTC
October 24, 2016 06:29 pm UTC
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Jason Drew Online content
Insane Member
Jason Drew  Online Content
Insane Member
*****
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Originally Posted by Mike Kuttschrutter
Originally Posted by Jason Drew
It lasts a while, I go through about 3-4 gallons of mix over the summer.


ummm? I go through my 2 gallon tank in a weekend.... wtf must be siphoning like crazy.... this is good to know


I used a lot more on a hobbs switch, when activating by load you'll find you use a lot less.


1997 Eclipse GST - AWD swapped - TPC - GT Spec powered
2023 - 9.63 - 145mph
Re: installed meth and looking for advice [Re: John MacPhail] #451463
October 24, 2016 07:52 pm UTC
October 24, 2016 07:52 pm UTC
Joined: Aug 2009
Posts: 4,783
Belleville Ontario
Jay Stacey Offline
Senior Member, with Far TOO Much Time on Their Hands
Jay Stacey  Offline
Senior Member, with Far TOO Much Time on Their Hands
*****
Joined: Aug 2009
Posts: 4,783
Belleville Ontario
This is the pump I use. The 2 wire switch on the end is an over pressure cut off. If the nozzle clogs or what ever.. The pump shuts off.


[Linked Image]

This is the circuit I made. I ran a wire off the pump side of the over pressure switch. This wire runs to a pressure switch by the nozzle with an inline dash light. When the nozzle sees 35psi+ fluid pressure the pressure switch turns on the light. If not enough pressure, the light doesn't turn on.

So if there is too much pressure, the pump shuts off and so does the light.

Then I have a relay inline this circuit, that activates the idle switch pin. This switches to Aux maps.

So when egr turns on water injection. The fail safe wire activates the dash light and the aux map.

So if nozzle clogs. Light goes out.. Switches to base map..

Hose comes undone.. Light goes out Switches to base map

Run tank empty.. Light goes out Switches to base map.

[Linked Image]

So far it works well.. But I stripped the threads in my check valve so it's on hold till spring. I was running 7g nozzle .. 5 parts water 2 parts meth. Didn't seem to effect the a/f but dropped temps everywhere and eliminated knock at 25psi and 14°timing.

Last edited by Jay Stacey; October 24, 2016 07:55 pm UTC.

11.45@125,
stock bottom end 6bolt 2g head.
272 hks cams.
Holset hx35
Backyard biult!!
Re: installed meth and looking for advice [Re: John MacPhail] #451464
October 24, 2016 08:21 pm UTC
October 24, 2016 08:21 pm UTC
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Bryan Lawrence Offline
Senior Member, with Far TOO Much Time on Their Hands
Bryan Lawrence  Offline
Senior Member, with Far TOO Much Time on Their Hands
***
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Where in link is the setting to switch maps


"Old Blue" 91 Talon TSi AWD
"Super Enthusiast" 91 Talon TSi AWD
Checkout DSMFAQ.com!
Re: installed meth and looking for advice [Re: John MacPhail] #451465
October 24, 2016 08:24 pm UTC
October 24, 2016 08:24 pm UTC
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
Jason Drew Online content
Insane Member
Jason Drew  Online Content
Insane Member
*****
Joined: Mar 2009
Posts: 3,055
Stanstead, Quebec
In the AuxMaps tab.


1997 Eclipse GST - AWD swapped - TPC - GT Spec powered
2023 - 9.63 - 145mph
Re: installed meth and looking for advice [Re: Jason Drew] #451466
October 24, 2016 08:24 pm UTC
October 24, 2016 08:24 pm UTC
Joined: Dec 2006
Posts: 1,287
ontario
Sven Hebbard Offline
Serious Member
Sven Hebbard  Offline
Serious Member
***
Joined: Dec 2006
Posts: 1,287
ontario
Originally Posted by Jason Drew
Originally Posted by Sven Hebbard
I've never understood.

Whats the point of mixing meth with water?

Meth has a flash point of almost double then gasoline, And it's a self cooling fuel. We battle freezing injectors open on the Rail car all the time.


It depends what you're using it for, if you want the cooling effects, water absorbs much more heat than meth. Obviously if you just want an octane boost, the more meth the better.

The #1 reason is safety, you can't see a methanol fire, supposedly concentrations 50% and below are not flammable.



For the amount of Meth that we use here I wouldn't see it being a issue. Also the Methanol has cooling property far superior to water.. On our rail car after running 168mph on the 1/4 the Blower is ICE cold(in a 32c day you'd think you stuck your hand on a bag of ice)

If you treat methanol with respect you won't have issues.

Page 1 of 2 1 2

Powered by UBB.threads™ PHP Forum Software 7.6.1.1