Previous Thread
Next Thread
Print Thread
Rate Thread
HOW TO: 2g ECU in 1G adapter harness #451593
November 04, 2016 04:07 am UTC
November 04, 2016 04:07 am UTC
Joined: Dec 2006
Posts: 1,287
ontario
Sven Hebbard Offline OP
Serious Member
Sven Hebbard  Offline OP
Serious Member
***
Joined: Dec 2006
Posts: 1,287
ontario
I had a couple member ask me to do a write up so i'll toss one together here.

What needed:

-Solder gun(Solder sucker or wick as-well)
-Shrink wrap
-Wire strippers
-Some wire
-A spare 1g ecu(i recommend a fried or non eprom ecu)
-A 2g Interior harness and engine harness
-Some patience

Procedure:

BEFORE BEGINNING REVIEW REVIEW REVIEW the 1g and 2g pin outs!!


Step 1:

Take the 1g spare ecu spare and de-solder the plug in from the board(The longer the pins the better contact area you will get), Take your time doing this, it can be a pain.

Step 2:

Take your 2g engine harness, Cut the ecu plugs off(Leaving about 6-8" to work with). Now take your 2g INTERIOR harness and cut the OBD2 port off.

Step 3:

Review this Image with the 2g pin outs with the 1g pin outs in RED

*** please remember the orientation of the pin outs facing you in diagrams***
[Linked Image]
[Linked Image]

Step 4:

Start stripping the wires ONE at a time on the 2g plugs and solder them to the 1g pin out, As your doing this DON"T FORGET TO PUT SHRINK TUBE ON THE WIRES BEFORE SOLDERING!!!! you'll want to shrink the tube on the connections later to not worry about shorting out between each-other. Also note some of the wire colors don't match, so worry about PIN OUTS not the wire color codes

*** I used the tinning method as keeping the solder gun on the 1g pin out will actually melt the plastic and the pins become loose. So tin the wire and tin the pin allow to cool, then solder together***

Step 5:

You should be at a stage like this, If you are CONGRATS your almost there. Continue to till all your wires are together, Heat shrink all the tubes up.
[Linked Image]


Step 6:

You need to solder 4 wires from the harness to the OBD2 plug. refer to ecmlink wiki for the pin outs you need.

***I put my obd2 port in the plastic spacer under my deck, lengthen your wires to where you want to place it***

https://www.ecmtuning.com/wiki/connectionproblem

Step 7:

You should be pretty much ready to slam your 2g ecu in your 1g car now! So go plug it all in!
[Linked Image]

Step 8:

You MUST USE A 2g ignition firing order!


Step 9:

Turn your ignition forward and try to connect to ecmlink, If you can great!! start a live capture and play with your throttle to make sure it's reading. If not, you will have to go back thru your wiring to make sure it is all correct.

Step 10:

ENJOY!



I have to give a huge shout out to the following for helping me gather this information for me to even be able to do this to my car!

-Slowcon(ecmlink)
-Junfan(dsmtuners)
-Hal(dsmtuners)

Last edited by Sven Hebbard; November 04, 2016 04:09 am UTC.
Re: HOW TO: 2g ECU in 1G adapter harness [Re: Sven Hebbard] #451594
November 04, 2016 09:36 am UTC
November 04, 2016 09:36 am UTC
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Bryan Lawrence Offline
Senior Member, with Far TOO Much Time on Their Hands
Bryan Lawrence  Offline
Senior Member, with Far TOO Much Time on Their Hands
***
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Nice work brother!!

Love the ghetto ecm link decal on the ecu!


"Old Blue" 91 Talon TSi AWD
"Super Enthusiast" 91 Talon TSi AWD
Checkout DSMFAQ.com!
Re: HOW TO: 2g ECU in 1G adapter harness [Re: Sven Hebbard] #451678
November 13, 2016 04:53 pm UTC
November 13, 2016 04:53 pm UTC
Joined: Dec 2006
Posts: 1,287
ontario
Sven Hebbard Offline OP
Serious Member
Sven Hebbard  Offline OP
Serious Member
***
Joined: Dec 2006
Posts: 1,287
ontario
PLEASE NOTE THIS!!!

5--->68 ISC motor coil (B1) 18---->67 ISC motor coil (B2)


After some testing you need to swap these wires to have proper control without reversing polarity's on the ISC


Powered by UBB.threads™ PHP Forum Software 7.6.1.1