1G AWD Partout 10.0 @ 139
#347306
February 27, 2011 05:51 pm UTC
February 27, 2011 05:51 pm UTC
|
Joined: Mar 2001
Posts: 1,004
Portland, OR
toddmeunier
OP
Serious Member
|
OP
Serious Member
Joined: Mar 2001
Posts: 1,004
Portland, OR
|
You guys might be interested in some of this. I do still have the Ontario ownership for the car as well. Prices do not include shipping or paypal fees All parts have mostly track only miles $250 Mishimoto rad with 2 12" pusher slim fans $400 1G JMF polished race intake manifold stock throttle body flange $450 DSM link V2 with 91 ecu (comes with a Mastah tune!) $200 1000cc injectors $100 Crower valve springs with titanium retainers $500 Kinetic (SBR) race FMIC with aluminum pipes, HKS BOV and NT throttle body $50 MAFT with 3" MAF and couplers $125 Innovate LC1 wideband with sensor and weld in bung $100 AEM 5 bar map sensor $75 Jay Racing alternator relocation kit $50 like new 6 bolt lower timing cover - installed and idled that's it $50 fuel rail with spoolinup afpr and pressure gauge $75 gloss black powdercoated valve cover $225 Scat 6 bolt h beam rods with 1000 miles $75 reground cams to HKS 272 $1500 0.82 AR T3 GT3582R with SFP manifold 3" complete exhaust, oil and water feed and drain lines 40mm tial and dump tube $75 4 inch turbo intake with massive K&N $100 3" exhaust with Apexi downpipe $400 good stock 6 bolt bottom end (ran 10.08@139) includes water pump front cover, timing etc... $100 6 bolt head with with cams and 90K miles $150 6 bolt bare head with recent rebuild. will need new valve seals $100 6 bolt head with stock springs (I think it has a bent valve) 2000 miles since rebuild $50 6 bolt rods $200 Good 6 bolt crank and block just needs pistons and rods $200 6 bolt bottom end. compression was around 120 $90 Kiggly 6 bolt flex plate - new in box 3x 1 gallon jugs of methanol $10 each $2500 Rolling shell - Very clean with clean KY title http://www.youtube.com/watch?v=qKg8UQLVl1gGood 17" wheels 235/40/17 tires with good tread AGX struts and apex/Megan springs shep clutch pedal assembly 91 shifter with new weighted 2G leather shift knob big brakes with new rear calipers and Hawk pads 4 bolt rear diff poly motor mounts and solid roll stop active toe eliminated boost/EGT/AFR gauges Bad No stereo No headliner Paint job was very expensive and color change was done correct. Car has been garaged since 2002. With a good engine and trans this will make someone a nice clean 1G. Sway bars have been removed in order to achieve 1.4 second 60 foot times. Pick up only 2x 3 bolt rear diffs = free 3 bolt rear axles = free email please toddmeunier@hotmail.com
90 Talon 10.089 @ 139.34
Mastah-tuned
TPG + Meth
|
|
|
Re: 1G AWD Partout 10.0 @ 139
[Re: toddmeunier]
#347381
February 28, 2011 03:22 pm UTC
February 28, 2011 03:22 pm UTC
|
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Bryan Lawrence
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
|
$100 3" exhaust with Apexi downpipe
I assume that this is full exhaust, I have a question though, is it stainless steel? if it is I would be interested.
"Old Blue" 91 Talon TSi AWD
"Super Enthusiast" 91 Talon TSi AWD
Checkout DSMFAQ.com!
|
|
|
Re: 1G AWD Partout 10.0 @ 139
[Re: toddmeunier]
#347385
February 28, 2011 06:40 pm UTC
February 28, 2011 06:40 pm UTC
|
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
Bryan Lawrence
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
|
Would you ever be in the area?
"Old Blue" 91 Talon TSi AWD
"Super Enthusiast" 91 Talon TSi AWD
Checkout DSMFAQ.com!
|
|
|
|
|
