Not sure exactly, but somewhere around $165. - $180. I am guessing...

Actually Ziggy consider me in. I will figure out the mounting when I get it.

1. Mike Eng -2g catch can, -10an, polished, vented, dual inlets
2. Andrew Trapp -2g catch can, -10an, powdercoated, dual inlets, vented
3. Kyle Guba -2g catch can, -10an, polished, vented, dual inlets. -2g catch can, -10an, polished, vented, dual inlets
4. Jason Drew -2g catch can, -8AN and recirc, Raw
5. Pedro Suarez- 2g catch can
6. Bryan Lawrence -2g catch can, -10an, powdercoated, recirc -12an
7. Rob Cauduro -2g catch can, -6AN inlets and recirc, Raw
8. Andrew Trapp - 2g overflow tank: -4 AN inlet, -8 AN outlet, powder coated 'satin black'

Thanks Kyle!

Hey Ziggy, can we get an update on this?

Also would like to know what has happened so far (ex. paid deposit, submitted list...)

I have paid in full to Andrew on Jan. 15th. He expected lead times on the catch cans to be short, but the overflow would take a touch longer. I asked that he ship everything together to save shipping cost. Even as it is, shipping still within the US is $45. USD for the single order. I would think I will contact him again in another week or so and see where things stand.

Ok sounds good, thanks for the update.

Hoping I can get this piece of art in my engine bay soon.
This is going to make my bay look much nicer and clean everything up.
Beautiful valve cover is going on with this thing too!

Ditto

Latest update is that he is almost done. I MIGHT see these this Friday night, otherwise it will be the following week.

Another setback. Apparently Andrew just bought a CNC lathe and has been busy re-doing his shop to get it in, so everything has been delayed. Looks like it will be after I get back from Florida.....sorry about that guys, but out of my control..

Do we get any pictures!?

Dang coulda picked them up on my drive home

Shamelessly borrowed from tuners.

Oh Nice, Mine will look similar to that as I got the powder coating!
I wonder why he has the two outlets on top?

I believe he specified to have the logo polished (paid extra).

Three lines are inlet from the VC in this particular setup.

Oh ok, good to know.

I think I may have say that setup and was freaking out cause I only wanted the one outlet and two inlets.

Sorry to be the bearer of bad news, but I just got an email from Andrew saying that when he recently received his new CNC Lathe (making me jealous), he squashed two fingers in moving it (I am NOT jealous of that part). He has been unable to do much, and has a helper finishing off the last of our order. He HOPES to ship by Friday, which means I would receive March 15th.

Damn, was hoping that you would have them this week so I could just do one big order.

Can't wait to have my hand on it!!

Keep your fingers safe Ziggy!!

frack that's painful.

Keep us posted Ziggy!

Send me one he did not the new guy

Just got an email from Andrew saying his hand is feeling better, and he should be able to finish our stuff in the next few days. That would mean I WON'T be receiving it this week

I REALLY hope that you guys understand that all this delay is beyond my control....

It's fine Ziggy! I know for most of us, our cars are still stored. So at least for me there isn't any urgency!

Thanks for the updates!

Haha Mike, lots of urgency here, I want this thing on my car soon, along with a matching valve cover, but I realize Ziggy is doing his best and that's all we can ask for!

Shouldn't you fix your wheel bearing first?

Just did it today next is the rear quarter panel

Hey Ziggy, can we get another update please.

I received this message from him in an email on Thursday. I have written him several times since, but still no response.



I was trying to get onto his website to check out a driveshaft loop, and his site seems to be down....:(

He did send me a pic of a batch of the cans...so hopefully soon.

VERY SORRY this is taking so long, but it is out of my control.

I know Ziggy, thanks for the update.

Nice you work fast lol



No worries Ziggy. I'm actually starting to consider road tripping down to Niagara with gf for a weekend in a couple weeks or so. It's in the air, but in talks. So maybe I can save on some shipping

Andrew is a one man show, he's a very busy guy. His lead times are way off, but I'm sure you guys will all get your parts... Some day.

When I deal with him he doesn't accept my payment until the part is ready. Probably because he doesn't want to leave me hanging.

It seems to happen in bursts, I will go a while without doing work then get a bunch done!

In my case he wanted payment up front, I am sure because he didn't want to be stuck with them himself. It seems he custom makes each piece, he doesn't "stockpile" anything..

What's the word Zig?

It's official. I'm heading back down there in 2 weeks.

So the weekend of April 13th. MY 29th birthday yippy!

Just heard from him that he is sending all but one catch can and the overflows this week. I HOPE they arrive for Friday. The missing catch can I believe will be Rob C's. He is waiting on -6 an male weld on bungs.

Ziggy

YAY! Glad to hear it!

AWESOME!

Well Brian, guess they didn't arrive???
Lol

You guys really struggle with my name don't you!!

Yeah I was hoping for an update, but it doesn't look like it

Bad news guys,..I got an email from Andrew saying that the -6 an bungs he was missing came in the day after he emailed, so he held back in order to finish everything off and ship all together. I told him there was a lynch mob slowly forming, and he said to send them his way.
I am not really pleased with this either. He has had a few thousand dollars of my money for a few MONTHS now......

I ASSUME we will get EVERYTHING next weekend....