11 sec DSM Part out
#126616
October 05, 2005 02:29 am UTC
October 05, 2005 02:29 am UTC
|
Joined: Mar 2005
Posts: 407 Hamilton
Victor Gerena
OP
pruned
|
OP
pruned
Joined: Mar 2005
Posts: 407
Hamilton
|
1g 1990 Rolling Shell, with 235k on it. This shell was repainted 3 years ago and looks pretty good. Could use a good detail. Would be perfect for a project car. Includes rear end, brakes, stock shocks/springs, alot of the front suspension was replaced(ball joints, tie rod ends, sway bar links). Has some fender rust and rust around door sensors. Underneath is awesome condition. This is AWESOME project shell ready for motor and tranny. $500
1G 6bolt JDM Motor with receipt, ~85k on this motor. The head has never been off the block and the oil pan has never been dropped. Compression is 157 157 155 152 cold with closed throttle plate. This motor was awesome, always ran good and i never used anything other then 10w30 Mobil 1 synthetic. The head looks mint, has some lifter tick. Includes everything from intake manifold down to flywheel. No accesories. $750
Mitsubishi Td06 20g Turbo. This turbo is mint and spools awesome.I got full boost by 3800rpm and flowed close to 400hp. It is setup for an external gate. The exhaust housing has been ported. Only problem is 2 manifold bolts warped and it will need to be helicoiled. No big deal. The compressor housing is polished, the wheels are mint and there is NO SHAFT play. Includes manifold gasket. Before i put this turbo on i had it rebalanced and fully cleaned by cherry turbos. If Herman remembers he will tell you this turbo was mint. About 2500km on this. $725
Tial 38mm with 1bar spring and 2.5" Tubular 02 housing dumped to atmosphere high heat coated. This setup was awesome, i had no boost creep and it sounded sick. Fits around everything and dumps right underneath the car. 1 bar spring in the tial, only 700km on both. Paid alot for this asking $475 for entire setup with bolts.
2g Exhaust Manifold, lightly ported and no cracks at all. Tapped for EGT. $100
3" VRS SS Downpipe, this downpipe fits like stock and the craftsman ship is great. 2.5" Pressbent catback with 3" SS muffler and a 2.5" testpipe. Complete exhaust setup, direct bolt up. $470 for entire setup. Catback and muffler came with car and have receipts for them.
Walbro 255HP Fuel pump with the fuel pump assembly. The line was replaced with a SS line and is a direct drop in. Totally replaces the stock rotted line and gets rid of that leaky o ring setup. Tap this right into the rubber fuel line in the rear. Fitting included. $175 Pump has 1000km on it. Includes 14V rewire kit as well.
Denso 660cc Fuel injectors. These are the BEST injectors you can get for DSM since the flow pattern is the same as stock. These have been rebalanced 15k ago to 1% within each other. Flow close to 720cc @ 45psi. Asking $300
Aeromotive 13101 AFPR with guage and -8 SS Line with fittings to fuel rail, from fuel rail to brand new filter -6 SS. Including the rail and filter. Complete fuel kit, last you will ever need. $360 for it all. Paid ALOT for this setup. Not even 700km on the afpr.
Buschur Racing Street FMIC kit with spearco 2-120 Intercooler and SS pipes. Complete kit with couplers, tbolt clamps, 2g elbow. The intercooler is THE BEST street core for the dsm. Flows enough to support 600hp. The bottom is a bit dented but has NO LEAKS. Tested to 35psi. SS pipes really bring out the engine bay. Asking $700 for this kit.
Competition Clutch 2500lb Ironmen kit, includes 6 puck disc and 2g disc. About 5000km on this setup. $225
Apexi SAFC in perfect working order, screen has some scratches expected from usage. Great to tune with. $200
91-94 EEPROM ecu mint board fully socketed by Rob Greer( CLEANEST SOCKET JOB EVER), with quick disconnect socket. Includes stock chip, i will include a chip set for 2g mas, 660cc, 5000 stutter, NLTS, 11.5:1 A/F, and alot more goodies. $325
2g Mas unhacked with 3" pipe, coupler, coupler to turbo and clamps. Includes filter with 200km on it, and harness adapter for plug and play $150.
Greddy 1.5bar boost guage - $80 Greddy EGT guage needs new probe $110 VDO electronic fuel pressure guage - $70 Guage pod for 2 Greddy Guages with black apillar - $40
Apex 1.7" Lowering Springs with stock shocks. Pretty stiff ride, will need camber adjustment. $140
Kumho 711 Ecsta Tires 8000km on 1g black swirlie rims. $250
Greddy TRUST Front Strut Bar, these are discontinued and rare. $50
Momo Race wheel with hub, awesome feel. $75
Leather front and rear seats, driver side has cut - $100
90 AWD Transfer case, new seals no leaks $70
90 AWD Transmission, 2nd gear synchro is toast, All other gears mint. $50
Toshiba Satellite logging laptop with carrying case - $75
90 Harness with 91+ Ignition Transistor conversion, just AC sensor at thermostat cut out, and afc cuts. $50
Other misc stuff i am forgetting just ask. Accept paypal you add 3%, email money transfer and money orders. Ship everything but the motor. PICS OF EVERYTHING available upon request. Thanks ca.dsm
|
|
|
Re: 11 sec DSM Part out
#126621
October 05, 2005 12:51 pm UTC
October 05, 2005 12:51 pm UTC
|
Joined: Mar 1999
Posts: 43 Markham, Ontario, Canada
Glenn Soriano
Race Seat King
|
Race Seat King
Joined: Mar 1999
Posts: 43
Markham, Ontario, Canada
|
I'll take the Momo Race steering wheel as long as it's leather (not the urethane model) Momo Race wheel with hub, awesome feel. $75
92 Tsi AWD, 6bolt, EvoIII mani/B16G/O2, 12x24x3 FMIC, 2.5" UICP, Blitz BOV, RC750, Paxton FPR, Walbro 255, 3" exhaust, ACT2600, ACT flywheel, Power Ent t-belt, HKS EVC IV, e-Manage, Koni yellows, H&R red, 2G brakes, Hawk HP+, SS brake/clutch lines
|
|
|
|
|