How the heck . . .
#185204
June 05, 2000 09:26 pm UTC
June 05, 2000 09:26 pm UTC
|
Joined: Mar 1999
Posts: 1,927 Ottawa, Ontario
Scotty Williams
OP
Serious Member
|
OP
Serious Member
Joined: Mar 1999
Posts: 1,927
Ottawa, Ontario
|
How the heck are you suppose to turn the crankshaft sproket counter clockwise (to remove the sproket to get the T-Belt off) WITHOUT turning the timing belt counterclockwise? The haynes manual says put a screwdriver between the driveline and flywheel sprokets (which I have no idea where they are) and the VFAQ says use a "special tool". Can I put a screwdriver b/w the two camshafts and remove the crankshaft bolt or is that bad?
Thanks! Scotty.
1990 Eagle Talon TSi AWD
|
|
|
Re: How the heck . . .
#185206
June 08, 2000 03:16 pm UTC
June 08, 2000 03:16 pm UTC
|
Joined: Jan 2000
Posts: 7,503 Trenton, On, Canada.
Ghislain Goudreau
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: Jan 2000
Posts: 7,503
Trenton, On, Canada.
|
The best result I had was to go to a garage and losen the bolt using an impact. You then retorque the blot and drive the car home. It's alot easyer to remove it after, but it's not always practical specially if you already have half of the engine apart...
An other way would be if you remove the valve cover you will see a place on the camshaft were you can put a wrench. I also used a clean peice of 2"x4" so the wrench would not damage anything. That works good to remove the cam sprokets .
I don't know if it would work to remove the cranck sproket bolt. You would have to do this before you remove the tensionner. I'd give this a try but be carefull. Have a look good at it first.
Good luck Dude.
Ghislain.
Rouge!!!
|
|
|
Re: How the heck . . .
#185207
June 09, 2000 06:43 am UTC
June 09, 2000 06:43 am UTC
|
Joined: Jul 1998
Posts: 234 Waterloo, ON
Matt Pratola
Serious Member
|
Serious Member
Joined: Jul 1998
Posts: 234
Waterloo, ON
|
This is documented in the VFAQ, at least it was the last 2 times i did it :> You use a breaker bar with a socket on the crank bolt and tirp the starter really quick, like half a second, not even. But go through the VFAQ and make sure you understand how to do it, and the risks of doing it. I didn't have any problems, but YMMV :>
Matt 92tsiAWD
95tsiAWD - the mean funky green machine RIP: 92tsiAWD 6/4 - taken out by hood opening @ 90kph
|
|
|
Re: How the heck . . .
#185208
June 09, 2000 11:17 am UTC
June 09, 2000 11:17 am UTC
|
Anonymous
Unregistered
|
Anonymous
Unregistered
|
I used my lug wrench (T type)on center bolt which a friend holds firmly in place. Then use a breaker bar with socket on bolts connecting the camshaft pulley wheel and undo that way. It is a tight fit with two sets of hands in the wheel well, but it works and you do not have to get an impact wrench or take off the valve cover.
I also tried to remove by putting the car in 1st gear and have heard of the starter trick, but these did not work for me.
Good Luck
|
|
|
|
|