Re: Just Chipped The S4
[Re: Troy Jollimore]
#284803
November 28, 2008 04:30 pm UTC
November 28, 2008 04:30 pm UTC
|
Joined: May 2003
Posts: 7,263 Niagara Falls, Ontario
Ziggy Dietrich
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: May 2003
Posts: 7,263
Niagara Falls, Ontario
|
Hey, can you guys tell me...does your shift knob thread on? If so, what thread is it?? I wouldn't mind doing a couple with the Audi logo and just putting them on my site....something like: https://www.rtmracing.com/xcart/product.php?productid=16213&cat=311&page=1
"bluebird" worlds fastest scooter ridden by me "Whitebird" RIP
|
|
|
Re: Just Chipped The S4
[Re: Grant Redfern]
#284810
November 28, 2008 05:24 pm UTC
November 28, 2008 05:24 pm UTC
|
Joined: May 2003
Posts: 7,263 Niagara Falls, Ontario
Ziggy Dietrich
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: May 2003
Posts: 7,263
Niagara Falls, Ontario
|
Well, I wouldn't do a special shape unless I had a ton of orders to make it worthwhile....but I will do a few with the correct thread and the Audi logo when I get a chance. I don't imagine that anyone has the Audi logo in a format my CAD can read? .igs, or .dxf??
"bluebird" worlds fastest scooter ridden by me "Whitebird" RIP
|
|
|
Re: Just Chipped The S4
[Re: Rob Strelecki]
#284821
November 28, 2008 06:35 pm UTC
November 28, 2008 06:35 pm UTC
|
Joined: May 2003
Posts: 7,263 Niagara Falls, Ontario
Ziggy Dietrich
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: May 2003
Posts: 7,263
Niagara Falls, Ontario
|
Ya, the C7P ones were nice....but they were still my standard shape, just custom logo. My cad lists TONS of formats, but not .cdr. Worst case would be to get a .jpg and redraw it myself in CAD.
"bluebird" worlds fastest scooter ridden by me "Whitebird" RIP
|
|
|
Re: Just Chipped The S4
[Re: Troy Jollimore]
#284862
November 28, 2008 11:29 pm UTC
November 28, 2008 11:29 pm UTC
|
Joined: May 2003
Posts: 7,263 Niagara Falls, Ontario
Ziggy Dietrich
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: May 2003
Posts: 7,263
Niagara Falls, Ontario
|
Already done.....was just a case of scale and spacing...Printed up a logo, took a couple measurements, and did a little math....program is written....will probably engrave one in time for the YD meet...just not sure if I will have time to thread it to suit the Audi. Are you planning to be at the meet, Grant?
"bluebird" worlds fastest scooter ridden by me "Whitebird" RIP
|
|
|
Re: Just Chipped The S4
[Re: Grant Redfern]
#284905
November 29, 2008 01:03 pm UTC
November 29, 2008 01:03 pm UTC
|
Joined: May 2003
Posts: 7,263 Niagara Falls, Ontario
Ziggy Dietrich
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: May 2003
Posts: 7,263
Niagara Falls, Ontario
|
Well, being stainless it is not THAT easy to tap...and I also still need to drill it out. I have them pre-drilled for the M10 x 1.25 thread that the DSM's use. I should find time today to get one drilled, tapped, and engraved...
"bluebird" worlds fastest scooter ridden by me "Whitebird" RIP
|
|
|
|
|