Used Mitsu TOB
#350161
April 10, 2011 11:11 pm UTC
April 10, 2011 11:11 pm UTC
|
Joined: Oct 2009
Posts: 49 London, Ont
Nathan Taback
OP
Newbie on Probation
|
OP
Newbie on Probation
Joined: Oct 2009
Posts: 49
London, Ont
|
Im wondering if someone held onto there old TOB that they replaced? Im looking for a OEM mitsu TOB. It must look like the attached image. An easy way to tell if its an OEM mitsu is if it has the tabs on the side that i have highlighted. If someone has one i would be interested in purchasing it. Thanks, Nathan Uploaded with ImageShack.us
Last edited by Nathan Taback; April 10, 2011 11:12 pm UTC.
|
|
|
Re: Used Mitsu TOB
[Re: Nathan Taback]
#350171
April 11, 2011 12:09 am UTC
April 11, 2011 12:09 am UTC
|
Joined: May 2003
Posts: 7,263 Niagara Falls, Ontario
Ziggy Dietrich
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: May 2003
Posts: 7,263
Niagara Falls, Ontario
|
I used to have a couple kicking around, and every time someone wanted one, I couldnèt find them. Then, out of the blue, they would show up again. I will have another look around.
I am surprised though that your fellow DSMers down there in Southwestern Ontario couldnèt help you out with this? In all their used junk parts, they don't have an OEM throwout bearing??
"bluebird" worlds fastest scooter ridden by me "Whitebird" RIP
|
|
|
Re: Used Mitsu TOB
[Re: mike leclerc]
#350210
April 11, 2011 12:57 pm UTC
April 11, 2011 12:57 pm UTC
|
Joined: Oct 2009
Posts: 49 London, Ont
Nathan Taback
OP
Newbie on Probation
|
OP
Newbie on Probation
Joined: Oct 2009
Posts: 49
London, Ont
|
I used to have a couple kicking around, and every time someone wanted one, I couldnèt find them. Then, out of the blue, they would show up again. I will have another look around.
Thanks Ziggy, Let me know what ya come up with. Hey. I got him one, but apparently there are different ones It was just the wrong one No worries Mike, i didnt realize there were other types either LOL
|
|
|
Re: Used Mitsu TOB
[Re: mike leclerc]
#350263
April 11, 2011 11:48 pm UTC
April 11, 2011 11:48 pm UTC
|
Joined: May 2003
Posts: 7,263 Niagara Falls, Ontario
Ziggy Dietrich
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: May 2003
Posts: 7,263
Niagara Falls, Ontario
|
Why....do we have enough of them elsewhere??? going to look right now. I know I went through this once already when someone else installed a PTT clutch...I think that is what this bearing is needed for, right? At the time I couldn't find them, but I have seen them since, so going searching now....
"bluebird" worlds fastest scooter ridden by me "Whitebird" RIP
|
|
|
Re: Used Mitsu TOB
[Re: Ziggy Dietrich]
#350264
April 11, 2011 11:58 pm UTC
April 11, 2011 11:58 pm UTC
|
Joined: May 2003
Posts: 7,263 Niagara Falls, Ontario
Ziggy Dietrich
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: May 2003
Posts: 7,263
Niagara Falls, Ontario
|
OK, found them, and guess they are NOT OEM. They Don't have those clips as per the picture. They are made by Nachi, so I think these were the bearings that come with ACT clutches....sorry about that...
But surely SOMEONE is changing a clutch or has an old TOB kicking around??
"bluebird" worlds fastest scooter ridden by me "Whitebird" RIP
|
|
|
Re: Used Mitsu TOB
[Re: Mike Kuttschrutter]
#350282
April 12, 2011 03:43 am UTC
April 12, 2011 03:43 am UTC
|
Joined: Oct 2009
Posts: 49 London, Ont
Nathan Taback
OP
Newbie on Probation
|
OP
Newbie on Probation
Joined: Oct 2009
Posts: 49
London, Ont
|
Why....do we have enough of them elsewhere??? going to look right now. I know I went through this once already when someone else installed a PTT clutch...I think that is what this bearing is needed for, right? At the time I couldn't find them, but I have seen them since, so going searching now.... Correct, this is why i need that style oem. Why....do we have enough of them elsewhere??? going to look right now. I know I went through this once already when someone else installed a PTT clutch...I think that is what this bearing is needed for, right? At the time I couldn't find them, but I have seen them since, so going searching now.... Thanks for looking Ziggy, i appreciate it. I gotz one for you Nathan! NICE!!!! send me a pm of what ya want for it and i can swing by and pick it up tomorrow if thats cool?
|
|
|
|
|