Re: Who runs Holset
[Re: ruben silva]
#367252
January 04, 2012 02:36 pm UTC
January 04, 2012 02:36 pm UTC
|
Joined: Jan 2006
Posts: 2,241 Stratford/London
Mike Kuttschrutter
Insane Member
|
Insane Member
Joined: Jan 2006
Posts: 2,241
Stratford/London
|
What a hacked drain I will get pics of mine tonight Some drain info from Holset: "Holset permits oil return pipes to decline at an overall angle of not less than 30 degrees below horizontal. All turbocharger applications require a pipe of internal diameter greater than 19 mm which has integrated connectors. To ensure oil returns into the engine under all operating conditions, the return connection into the engine sump must not be submerged and the outlet flange of the turbocharger must be 50 mm above the maximum oil level of the engine sump pan." so that 90 is a No-No
Last edited by Mike Kuttschrutter; January 04, 2012 02:46 pm UTC.
Stock.
|
|
|
Re: Who runs Holset
[Re: ruben silva]
#368751
February 07, 2012 07:40 pm UTC
February 07, 2012 07:40 pm UTC
|
Joined: May 2010
Posts: 1,106 Saskatoon, Saskatchewan
Andrew Trapp
Serious Member
|
Serious Member
Joined: May 2010
Posts: 1,106
Saskatoon, Saskatchewan
|
Can't speak from first hand experience on either, but from what I have read all over the forums are as follows:
SLS: top notch product, cheaper than PR, terrible customer service
PR: top notch product, more expensive than PR, good customer service
Both offer a lifetime warranty for the original buyer and both seem to fit holsets really nicely.
It pretty much comes down to - is the customer service worth a few $?
|
|
|
Re: Who runs Holset
[Re: ruben silva]
#376229
May 24, 2012 03:06 pm UTC
May 24, 2012 03:06 pm UTC
|
Joined: Oct 2010
Posts: 9,968 Caledon, Ontario, Canada
Bryan Lawrence
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
|
can you not go with a longer piece of hose and just do a little circle?
"Old Blue" 91 Talon TSi AWD "Super Enthusiast" 91 Talon TSi AWD Checkout DSMFAQ.com!
|
|
|
Re: Who runs Holset
[Re: ruben silva]
#376233
May 24, 2012 03:19 pm UTC
May 24, 2012 03:19 pm UTC
|
Joined: Oct 2010
Posts: 9,968 Caledon, Ontario, Canada
Bryan Lawrence
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
|
i couldn't find a picture to show you what I mean, but what about using smaller fitting and run it like this. http://www.dsmtuners.com/forums/att...4&stc=1&thumb=1&d=1283354451Ok good to know Rob.
"Old Blue" 91 Talon TSi AWD "Super Enthusiast" 91 Talon TSi AWD Checkout DSMFAQ.com!
|
|
|
Re: Who runs Holset
[Re: ruben silva]
#376235
May 24, 2012 03:48 pm UTC
May 24, 2012 03:48 pm UTC
|
Joined: Oct 2010
Posts: 9,968 Caledon, Ontario, Canada
Bryan Lawrence
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
|
To continue what Rob said, that is still downward and straight so that would work.
"Old Blue" 91 Talon TSi AWD "Super Enthusiast" 91 Talon TSi AWD Checkout DSMFAQ.com!
|
|
|
Re: Who runs Holset
[Re: ruben silva]
#376245
May 24, 2012 05:40 pm UTC
May 24, 2012 05:40 pm UTC
|
Joined: Oct 2010
Posts: 9,968 Caledon, Ontario, Canada
Bryan Lawrence
Senior Member, with Far TOO Much Time on Their Hands
|
Senior Member, with Far TOO Much Time on Their Hands
Joined: Oct 2010
Posts: 9,968
Caledon, Ontario, Canada
|
that looks ok, you just need to make sure that the lowest point is where it is connected to the oil pan and that the oil only goes down
"Old Blue" 91 Talon TSi AWD "Super Enthusiast" 91 Talon TSi AWD Checkout DSMFAQ.com!
|
|
|
|
|