Complete FP3065 setup
#391421
January 02, 2013 08:44 pm UTC
January 02, 2013 08:44 pm UTC
|
Joined: Dec 2000
Posts: 4,398 Ajax, ON
Reza Mirza
OP
Senior Member, with Far TOO Much Time on Their Hands
|
OP
Senior Member, with Far TOO Much Time on Their Hands
Joined: Dec 2000
Posts: 4,398
Ajax, ON
|
Up for sale is my complete bolt on dual ball bearing FP3065 setup that I have been running for the last few years. I have upgraded to a DSM HTA3586 and need to sell this one. There is absolutely NOTHING wrong with this turbo at all. I have put approx. 80k km on it and it is still as good as new. Turbo does not smoke, and has absolutely no play other than the normal axial play that any dual ball bearing turbo comes with. The turbo has been very reliable and has never let me down. I have boosted it as high as 40 psi and have seen near 75 lbs/min on this (which is almost unheard of on a FP3065). I ran 10.7 and trapped 136 mph running only around 35 psi on it. I also ran high 10’s on it running only 30ish lbs of boost. The compressor housing is polished and has an aluminium 90 degree welded on it for a 1g. If it will be used on a 2g, the 90 degree can easily be cut and re-welded in the opposite direction in order to accommodate your setup. I am selling this turbo as a complete package, so you also get the Tial 44mm wastegate with the maximum amount of springs in it, I believe the springs are around 20psi. FP dump tube for the Tial 44mm is also included along with the necessary v-band clamps for both the dump tube and wastegate. You also get the 2.5” FP vband O2 housing along with the necessary v-band clamp to attach it to the turbo. Also included is the oil feed line, nipples and SS braided lines for the coolant. Only thing I am NOT including is the oil drain and the FP oil filter. This is one badass turbo, anyone who buys this will not regret it one bit. You can come by and see it, I can start the car, and you can hear it spin down for well over a minute once the engine is shut off, unless I decide to take it off soon to take some pics.... Anyhow I want $1500 for everything, i.e. FP3065, Tial44 mm, FP O2 housing, FP dumptube, oil feed and coolant lines. A lot of people have seen my setup, it is mint, well kept and runs hard. I will put up pics once I take it off, though here is your chance to jump on it before the pics go up. Go look at the prices of turbos on FP’s website, along with the FP O2 housing and tial wastegates. New evo16g’s are selling for $1,200.00 now. $1,500.00 for everything. Low ballers will not be replied to
|
|
|
Re: Complete FP3065 setup
[Re: Reza Mirza]
#391605
January 04, 2013 09:15 pm UTC
January 04, 2013 09:15 pm UTC
|
Joined: May 2012
Posts: 217 alberta
James Devereaux
Serious Member
|
Serious Member
Joined: May 2012
Posts: 217
alberta
|
Im into this setup. You saw my previous post. I want to drag occasionally and I want to auto cross from time to time. looking for 450 to 500 running aem meth. does that work ?
2006 rr sport sc
|
|
|
Re: Complete FP3065 setup
[Re: Reza Mirza]
#391633
January 05, 2013 09:45 am UTC
January 05, 2013 09:45 am UTC
|
Joined: May 2012
Posts: 217 alberta
James Devereaux
Serious Member
|
Serious Member
Joined: May 2012
Posts: 217
alberta
|
my internals should back it up hey ? what cams would be good
2006 rr sport sc
|
|
|
Re: Complete FP3065 setup
[Re: Reza Mirza]
#391857
January 09, 2013 02:27 am UTC
January 09, 2013 02:27 am UTC
|
Joined: Dec 2000
Posts: 4,398 Ajax, ON
Reza Mirza
OP
Senior Member, with Far TOO Much Time on Their Hands
|
OP
Senior Member, with Far TOO Much Time on Their Hands
Joined: Dec 2000
Posts: 4,398
Ajax, ON
|
|
|
|
|
|