parting out my 1g, parts are cheap

http://www.kijiji.ca/v-view-details...uid=14614d79-beb0-a20b-2701-5335ffff25d9

Link no good. Takes you to an entire engine parts list.

Ill take the wires if you still have them on friday.

Link works, and where else would you put a full part out?

Must be my phone then cause kijiji says the add has been removed. And I am looking ford v8's and vw parts............

Link doesn't work for me either, why not just make up a parts list on here?

It's cause he posted the link to edit the add, get ready for some people having a little fun!

Oh ok ic I will post the list on here and here is the new link

http://www.kijiji.ca/v-engines-and-...94308606?enableSearchNavigationFlag=true

I am parting out my talon and all that is posted is still for sale and I will mark sold as they sell thank you

will also trade for gc8, sti parts.

-6 bolt 4G63 turbo SOLD
Balance shaft delete kit with mirage stub shaft
new top line oil pump housing
2nd gen 8.5-1 pistons on 1st gen rods
Clevite Race bearings
clearances unknown
larger PTW clearance
compression test on cold motor. #4-158 #3-155 #2-145 #1-140 see pics
only 1000km and I run the motor once a week as well since last year.

-1G 6 bolt head SOLD
OEM valvetrain
Port matched exhaust ports
ported oil path in block through cylinder head to compensate for larger head studs blocking oil path to head

-6 bolt arp head studs $50

-6 bolt stock head studs $40

-7 bolt head (head valves and springs unmolested) $100 pending

-7 bolt block crank and flywheel (not walked or blown) $100

-Transmission SOLD
Forcepower Stage 3 gear box
Welded Center Diff+ VC eliminated
Chromoly shift forks
DSM gear set
front cv shafts (passenger outer boot ripped but shaft is great)

-Stock T-case $80

-prop shaft $100 (new mitsu universal joint) pending

-Competition Clutch stage 4 sprung clutch and 2700 pressure plate on cc light weight flywheel $250

-Stock 4 bolt rear shafts cups and pumpkin subframe with adjustable toe $400

-Eibach Sport line springs on struts $100(front)
-Tein lowering springs $100 (rear)
or $100 for both with your old struts

-Energy suspension swaybar bushings front and rear $30 new in box

-stock dsm injectors $100

-Aeromotive fuel pressure regulator with -8an fuel line from fuel Rail to fpr with dsm fuel rail $100

-Walbro 255 intank fuel pump $40

-dual 10" derale slim electric pull/pull fan (set up pushing plug and play and brand new) on Stock radiator $250 pending

-blown TD05h 20G 3"compressor cover on 1g manifold (new turbine shaft needs bearings) SOLD

-stock 14b converted to downfiring $100
PTP Subaru Turbo blanket(beat but usable)

-2.5” intercooler piping long route $350
Custom intercooler W/ CAST endtanks rated 650hp
Turbosmart Race port blow off valve (ver 1)
GM AIT

-6 bolt stock intake manifold $10

-ForcePower Motorsports "Prototypes" Race Sheet Metal Intake Manifold polished ( works amazing) $300
Rebuilt stock 60mm throttle body

-p2r phenolic gaskets (both tb sides and im) $50 pending

-Custom Valve cover shaved polished with -12an Vent SOLD

-3” intake pipe with -12 fitting w 3" silicone and 3"-2 1/4"adapter $40

-DNP DSM equal length Tubular Exhaust manifold W/ 40mm wastegate flange and adapter (wrapped with DEI Titanium exhaust wrap twice)
Tial 38 Wastegate ( double springed blue for 24 psi) SOLD

- Full 3” Stainless Steel Exhaust , exhaust wrapped with DEI Titanium exhaust wrap from 02 to the cat
2.5" flange bolts to stock o2 housing
3" flex pipe
3” catiyltic converter
3” X 14” Vibrant stainless resonator
3” in 4” out Vibrant SS muffler $350 pending

-AEM EMS V.1 $600

-Master power 4-bar Map sensor $25

-aem 3.5 bar Map sensor (maybe a hour of use)$120

-1g coils $30

-1g igniter $40

-1g MPI $40

-1g starter rebuilt (done in 2011 low km) $100

-1g alternator rebuilt (done in 2011 low km) $100

-AEM Digital Wideband Sensor + gauge $140

-Stuart Warner electric Oil pressure gauge SOLD

-Stuart Warner Fuel pressure gauge SOLD

-Stuart Warner mechanical Boost Gauge -30hg to 40psi SOLD

-AEM Water/Methanol Injection kit w/1 Gallon tank $250 pending

tsi awd Exterior/Shell $300
190,000km, , well oiled chassis
custom Flat Honda Silver metallic/ Black Metallic (chipped by hail but no hail dents)
hole in rear behind gas tank

-new magnacore thundervolt wires $50

-2g MAF with filter $80

-stock 1gb head lights + markers $50 pending

-clear and blacked 1gb lights(led bulbs) + markers $120 pending

-1Gb Taillights $80

-Shifter base and solid bushings with cables $80

-complete power doors ding free hinges $140

- both fenders $80 (passenger side started to bubble)

-hatch with shocks and latch with full stock wing $150

-hood gutted vented and pinned with pins $80

-wiper motor assembly $60

-cowl cover black $5

-all 4 brake calipers $80 pending

-leather interior (front and rear seats) $120

-black carpet $40

-center console with gauge hole $20

-steering colum with grant hub and wheel $200

-front bumper $20

-rear bumper $20

-rear reinforcement bar $5

-all seatbelts $150

-dash ( + boulster and glovebox)$120

UPDATEED!!!!


-6 bolt 4G63 turbo SOLD
Balance shaft delete kit with mirage stub shaft
new top line oil pump housing
2nd gen 8.5-1 pistons on 1st gen rods
Clevite Race bearings
clearances unknown
larger PTW clearance
compression test on cold motor. #4-158 #3-155 #2-145 #1-140 see pics
only 1000km and I run the motor once a week as well since last year.

-1G 6 bolt head SOLD
OEM valvetrain
Port matched exhaust ports
ported oil path in block through cylinder head to compensate for larger head studs blocking oil path to head

-6 bolt arp head studs $50

-6 bolt stock head studs $40

-7 bolt head (head valves and springs unmolested) $100

-7 bolt block crank and flywheel (not walked or blown) $100

-Transmission SOLD
Forcepower Stage 3 gear box
Welded Center Diff+ VC eliminated
Chromoly shift forks
DSM gear set
front cv shafts (passenger outer boot ripped but shaft is great)

-Stock T-case $80

-prop shaft $100 (new mitsu universal joint) PENDING

-Competition Clutch stage 4 sprung clutch and 2700 pressure plate on cc light weight flywheel $250

-Stock 4 bolt rear shafts cups and pumpkin subframe with adjustable toe SOLD

-Eibach Sport line springs on strutsSOLD (front)
-Tein lowering springs SOLD (rear)
or SOLD for both with your old struts

-Energy suspension swaybar bushings front and rear $30 new in box

-stock dsm injectors $100

-Aeromotive fuel pressure regulator with -8an fuel line from fuel Rail to fpr with dsm fuel rail SOLD

-Walbro 255 intank fuel pump SOLD

-dual 10" derale slim electric pull/pull fan (set up pushing plug and play and brand new) on Stock radiator $250 PENDING

-blown TD05h 20G 3"compressor cover on 1g manifold (new turbine shaft needs bearings) SOLD

-stock 14b converted to downfiring $80
PTP Subaru Turbo blanket(beat but usable)

-2.5” intercooler piping long route SOLD
Custom intercooler W/ CAST endtanks rated 650hp
Turbosmart Race port blow off valve (ver 1)
GM AIT

-6 bolt stock intake manifold $10

-ForcePower Motorsports "Prototypes" Race Sheet Metal Intake Manifold polished ( works amazing) $300
Rebuilt stock 60mm throttle body

-p2r phenolic gaskets (both tb sides and im) $50 PENDING

-Custom Valve cover shaved polished with -12an Vent SOLD

-3” intake pipe with -12 fitting w 3" silicone and 3"-2 1/4"adapter SOLD

-DNP DSM equal length Tubular Exhaust manifold W/ 40mm wastegate flange and adapter (wrapped with DEI Titanium exhaust wrap twice)
Tial 38 Wastegate ( double springed blue for 24 psi) SOLD

- Full 3” Stainless Steel Exhaust , exhaust wrapped with DEI Titanium exhaust wrap from 02 to the cat $350 PENDING
2.5" flange bolts to stock o2 housing
3" flex pipe
3” catiyltic converter
3” X 14” Vibrant stainless resonator
3” in 4” out Vibrant SS muffler

-AEM EMS V.1 $600

-Master power 4-bar Map sensor $25

-aem 3.5 bar Map sensor (maybe a hour of use)$120

-1g coils $30

-1g igniter SOLD

-1g MPI $40

-1g starter rebuilt (done in 2011 low km) SOLD

-1g alternator rebuilt (done in 2011 low km) $100

-AEM Digital Wideband Sensor + gauge SOLD

-Stuart Warner electric Oil pressure gauge SOLD

-Stuart Warner Fuel pressure gauge SOLD

-Stuart Warner mechanical Boost Gauge -30hg to 40psi SOLD

-AEM Water/Methanol Injection kit w/1 Gallon tank $250 PENDING

tsi awd Exterior/Shell SOLD
190,000km, , well oiled chassis
custom Flat Honda Silver metallic/ Black Metallic (chipped by hail but no hail dents)
hole in rear behind gas tank

-new magnacore thundervolt wires $50

-2g MAF with filter $80

-stock 1gb head lights + markers SOLD

-clear and blacked 1gb lights(led bulbs) + markers SOLD

-1Gb TaillightsSOLD

-Shifter base and solid bushings with cables SOLD

-complete power doors ding free hinges SOLD

- both fenders SOLD (passenger side started to bubble)

-hatch with shocks and latch with full stock wing SOLD

-hood gutted vented and pinned with pins SOLD

-wiper motor assembly SOLD

-cowl cover blackSOLD

-all 4 brake calipers $80

-leather interior (front and rear seats) SOLD

-black carpet SOLD

-center console with gauge hole SOLD

-steering colum with grant hub and wheel SOLD

-front bumper SOLD

-rear bumper SOLD

-rear reinforcement bar SOLD

-all seatbelts SOLD

-dash ( + boulster and glovebox)SOLD

Don't suppose you have a 1g knock sensor?

I might ill check

Yes I do have a 1g knock sensor

Also have 2g knock sensor as well

What will you take shipped for the 1g knock sensor?

Ill be heading up to Kenny u pull in hamilton next Saturday we can meet there save you shipping. $40 for the sensor

I wont be around buddy I will be in Alberta

Turns out I will be here on Saturday buddy.

Scratch that I'm back in alberta

updated list of everything whats left


-6 bolt arp head studs $50

-6 bolt stock head studs $40

-7 bolt block crank and flywheel (slight walk not blown) $50

-Stock T-case $80

-Competition Clutch stage 4 6 puck ceramic sprung clutch and 2700 pressure plate and cc light weight 6bolt awd flywheel $350

-stock 450cc dsm injectors $80

-stock 14b converted to downfiring no turbine housing & PTP Subaru Turbo blanket(beat but usable) $50

-6 bolt stock intake manifold $10

-ForcePower Motorsports Race Sheet Metal Intake Manifold polished with phenolic head to manifold gasket( works amazing) for 6 bolt head $300

- Full 3” Stainless Steel Exhaust , awd cat back $200

3” catiyltic converter
3” X 14” Vibrant stainless resonator
3” in 4” out Vibrant SS muffler

-AEM EMS V.1 with Master power 4-bar Map sensor $25 & aem 3.5 bar Map sensor (maybe a hour of use) $500

-1g MPI $40

-2g MAF with filter $80

- 90 dsm Shifter base solid bushings with $10

-all 4 brake calipers single piston $80











http://www.kijiji.ca/v-engines-and-...-turbo-stock-performance-parts/594308606

AEM EMS and Map sensors SOLD



-6 bolt arp head studs $40

-6 bolt stock head studs $10

-7 bolt block crank and flywheel (slight walk not blown) $50

-Stock 22 spline T-case $80

-Competition Clutch stage 4 6 puck ceramic sprung clutch and 2700 pressure plate and cc light weight 6bolt awd flywheel $300

-stock 450cc dsm injectors $80

-stock 14b converted to downfiring no turbine housing & PTP Subaru Turbo blanket(beat but usable) $50

-6 bolt stock intake manifold $10

-ForcePower Motorsports Race Sheet Metal Intake Manifold polished with phenolic head to manifold gasket( works amazing) for 6 bolt head $300

- Full 3” Stainless Steel Exhaust , awd cat back $200
3” catiyltic converter
3” X 14” Vibrant stainless resonator
3” in 4” out Vibrant SS muffler

-1g 3 MP's $40

-2g MAF with filter $60

- 90 dsm Shifter base solid bushings with $10

-all 4 brake calipers single piston $50

PRICE DROP!!



-6 bolt arp head studs $30

-6 bolt stock head studs $10

-7 bolt block crank and flywheel (slight walk not blown good for rebuild) $25

-Stock 22 spline T-case $60

-Competition Clutch stage 4 6 puck ceramic sprung clutch and 2700lb pressure plate and cc light weight 6bolt awd flywheel $250

-stock 450cc dsm injectors $60

-stock 14b converted to downfiring (can be clocked back to stock location,no turbine housing & also comes with PTP Subaru Turbo blanket beat but usable $50

-6 bolt stock intake manifold $10

-ForcePower Motorsports Race Sheet Metal Intake Manifold polished with phenolic head to manifold gasket( works amazing) for 6 bolt head $250

- Full 3” Stainless Steel Exhaust , awd cat back $150
3” magnaflow cat
3” X 14” Vibrant stainless resonator
3” in 4” out Vibrant SS muffler

-2 1g MPI relay's $30

-2g MAF with filter $50

-all 4 brake calipers single piston's $50

LAST PRICE DROP! PICK UP ONLY!

-6 bolt arp head studs $20

-6 bolt stock head studs $free

-7 bolt block crank and flywheel (slight walk not blown good for rebuild) $20

-Stock 22 spline T-case $50

-Competition Clutch stage 4 6 puck ceramic sprung clutch and 2700lb pressure plate and cc light weight 6bolt awd flywheel (lots of life left + alignment tool) $200

-stock 450cc dsm injectors $40

-stock 14b converted to downfiring (can be clocked back to stock location,no turbine housing & also comes with PTP Subaru Turbo blanket beat but usable $20

-6 bolt stock intake manifold $10

-ForcePower Motorsports Race Sheet Metal Intake Manifold polished with phenolic head to manifold gasket( works amazing) for 6 bolt head and stock tb $200

-2 1g MPI relay's $10

-2g MAF with filter $30

-all 4 brake calipers single piston's $40


or the STEAL DEAL $425 takes everything listed! do the math thats freaking awesome!

also on the list I missed

-green top CAS $30

-black top CAS $30